Misc Telemetry Tool for F1 22 12.4

[Iko Rein]

Nice one.

I've just noticed that there are several pages that seem to be for the same telemetry tool but all have different versions. Which is the main thread/which has the latest version?

Thanks

For now I follow the F1 release cycle, i.e. the major version gets updated, when new F1 game is released. So there is always the "latest" version in the last F1 game mod section, so here is the link: https://www.racedepartment.com/downloads/telemetry-tool-for-f1-23-and-many-other-games.61580/ for the current 'latest' version.

There is also link to the latest version from the https://telemetrytool.com

The Tool itself should also show during startup on the splashscreen , if there is an update available, and if you go to the 'Help -> About' it will show, if there is newer version available.

I keep updating the latest version on the latest F1 game section, but will add links to the older F1 games' mod section on release. For AC/ACC/AMS2/PC2/rFactor2 there should be the latest version too. This is due to the limitation of RD that you cannot have one "master mod" for all different games.

Cheers.

 

[Bou17]

Hi,

I did all the steps that are required to run the Telemetry tool for F1 2023 from the PS5. But, I can't see the data.

I put my IP adress in the game settings and activate it. And I restarted both after it.

I don't know what my issue is.

Thanks

 

[Iko Rein]

Hi,

I did all the steps that are required to run the Telemetry tool for F1 2023 from the PS5. But, I can't see the data.

I put my IP adress in the game settings and activate it. And I restarted both after it.

I don't know what my issue is.

Thanks

Few points to check:
1) Make sure the IP address is correct. In the Tool you could use the 'Tools -> Show my IP address' to see the IP address. If there are multiple options, you need to try each, if you are not sure about the correct IP address. Please note that on some configurations, your IP address might change between sessions.
2) Make sure in F1 23 game the UDP is enabled and it is in F1 23 mode and port is 20777.
3) Start the Telemetry Tool in F1 23 mode. Make sure the start-up splash screen shows the port number 20777. You can see the 'game mode' at the window title too.
4) Sometimes windows firewall (or other software firewalls) can block the incoming traffic, so check the PC's firewall's logs.

Cheers.

 

[Iko Rein]

Posted new 13.3 on the F1 23 mod page: https://www.overtake.gg/downloads/telemetry-tool-for-f1-23-and-many-other-games.61580/
Cheers.

 

[Pamini88]

On the website it says that it is possible to forward data to another PC so a race engineer can analyse it. But i can't find how to do that. Is there someone who can help me with that?

 

[Iko Rein]

On the website it says that it is possible to forward data to another PC so a race engineer can analyse it. But i can't find how to do that. Is there someone who can help me with that?

In short, enable UDP Redirect (in Settings --> Network Settings) and set in the race engineer's IP address. Race Engineer needs to be running the Telemetry Tool on that IP address. You can also see the help in the Tool about UDP redirect.

There might be need to open firewalls to let the traffic through. Easiest way to avoid "opening firewall) is to use VPN Tunnel, as it will take care of the routing between the two computers. Many of my users are using Hamachi VPN tunnel for this.

Cheers.

 

[Pamini88]

In short, enable UDP Redirect (in Settings --> Network Settings) and set in the race engineer's IP address. Race Engineer needs to be running the Telemetry Tool on that IP address. You can also see the help in the Tool about UDP redirect.

There might be need to open firewalls to let the traffic through. Easiest way to avoid "opening firewall) is to use VPN Tunnel, as it will take care of the routing between the two computers. Many of my users are using Hamachi VPN tunnel for this.

Cheers.

Thank you very much

 

[Iko Rein]

Hello,

Posted new 13.4 on the F1 23 mod page: https://www.overtake.gg/downloads/telemetry-tool-for-f1-23-and-many-other-games.61580/

Cheers.

 

[Pamini88]

Hello, I tried multiple times to connect this tool with my cousin, i want to try to be his race engineer, but we can't get it connected. Is there any way you can help me with it. Because we just dont understand it.

Thanks in advance.

 

[Iko Rein]

Hello, I tried multiple times to connect this tool with my cousin, i want to try to be his race engineer, but we can't get it connected. Is there any way you can help me with it. Because we just dont understand it.

Thanks in advance.

The issue is typically caused by the firewall in between or that the IP address is not correct.

To make the connectivity simpler, you could use VPN tunnel between your cousin and your system. I have heard many of my users using Hamachi, but I also have seem Radmin to be recommended for this. Using the VPN tunnel helps to avoid the need to know the exact IP and opening ports in Firewall.

For the help for Redirect, see the help in the tool (by pressing key F1).

Cheers.

 

[Tozzimario75]

pls video tutorial on YouTube Mac OS installation m1 arm

 

[Iko Rein]

There is tutorial for installing for mac already at

Telemetry Tool - MAC Install tutorial

Cheers.

 

[BABABANKS]

I have a question, I am doing a study as part of my studies on suspensions controlled via ACC so I am using the telemetry tool for ACC, so I am using the rotation and suspension movements function and I am using them compares according to different parameters on ACC. So currently I am comparing them visually but is it possible to extract from your tools a table of values with the values of each curve: suspensions, movements and rotation? because the goal would be to take an average of each value from the table retrieved to conclude the effectiveness of the different suspension settings depending on the sectors of the circuit. And currently I can't just rely on a visual to make these readings, I would need more precise values, and is it also possible to add a scale to the x-axis for the distance on the circuit? Thank you 1000x for your involvement.

 

[Michelive]

I have a question, I am doing a study as part of my studies on suspensions controlled via ACC so I am using the telemetry tool for ACC, so I am using the rotation and suspension movements function and I am using them compares according to different parameters on ACC. So currently I am comparing them visually but is it possible to extract from your tools a table of values with the values of each curve: suspensions, movements and rotation? because the goal would be to take an average of each value from the table retrieved to conclude the effectiveness of the different suspension settings depending on the sectors of the circuit. And currently I can't just rely on a visual to make these readings, I would need more precise values, and is it also possible to add a scale to the x-axis for the distance on the circuit? Thank you 1000x for your involvement.

All the data necessary for the creation of the graphs are present in numerical and tabular format within the CSV files in the LAPDATA folder. You might find what you need there.

Cheers

 

[BABABANKS]

All the data necessary for the creation of the graphs are present in numerical and tabular format within the CSV files in the LAPDATA folder. You might find what you need there.

Cheers

Ok I see, but with which software do you open the file? Because if I open it with a text software I have a very long series of numbers, 2500 lines that are displayed, all compacted and incomprehensible. Is there a specific place to open them apart from telemetry tool, or a way to understand the layout?

Thank you

 

[Michelive]

Ok I see, but with which software do you open the file? Because if I open it with a text software I have a very long series of numbers, 2500 lines that are displayed, all compacted and incomprehensible. Is there a specific place to open them apart from telemetry tool, or a way to understand the layout?

Thank you

You can open them with Excel or a csv viewer.

 

[BABABANKS]

You can open them with Excel or a csv viewer.

Yes it works on excel! Thanks!